-
11GASKET; clutch housing (see note A)
-
21OIL SEAL; OIL SEAL, transmission drive shaft front bearing retainer or planet carrier front bearing (see note A)
-
32PLUG; cup (for sealing torque amplifier clutch release shaft openings)
-
6BOLT Hex, 3/8'' - 16 x 5/8'', Gr 5, Full Thd;
-
6LOCK WASHER 3/8''; WASHER, LOCK, 3/8''
-
1WASHER 3/8''; (13/32'' ID x 13/16'' OD x no. 16 ga) 3/8''
-
51GASKET; clutch housing top cover (see note A)
-
11BOLT Hex, 3/8'' - 16 x 3/4'', Gr 5;
-
8BOLT Hex, 3/8'' - 16 x 3/4'', Gr 5;
-
71GASKET; clutch housing top cover cap (see note A) (not used on tractors equipped with electrall)
-
3BOLT Hex, 3/8'' - 16 x 3/4'', Gr 5;
-
3LOCK WASHER 3/8''; WASHER, LOCK, 3/8''
-
1DRAIN PLUG Sq Hd, 1/2''-14 NPTF; PLUG, , Pipe, C.I. Sq Hd, 1/2''-14 NPTF
-
9BOLT Hex, 5/8'' - 11 NC x 2-1/4'', Gr 5; SCREW, cap, hex-hd., 5/8-11NC x 2-1/4''
-
2STUD Hex, 1/2''-13 x 7 1/2'', G5; SCREW, cap, hex-hd., 1/2-13NC x 7-1/2''
-
2LOCK WASHER 1/2''; WASHER, LOCK, 1/2''
-
8LOCK WASHER 5/8''; WASHER, LOCK, 5/8''
-
1LOCK WASHER Ext Tooth, 5/8''; WASHER, LOCK, Ext Tooth, 5/8''
-
111SEAL; OIL SEAL, power take-off drive gear (see note A)
-
122STUD; DOWEL, engine rear support
-
141GASKET; power take-off driven gear cover (see note A)
-
151GASKET; seasonal disconnect or bottom cover (see note A)
-
9BOLT Hex, 3/8'' - 16 x 7/8'', Gr 5, Full Thd; cap, hex-hd., 3/8-16NC x 7/8''
-
1BACK-UP RING; jam, hex., 7/8-14NF
-
1O-RING 0.139'' Thk x 0.859'' ID, -212, Cl 5, 75 Duro; RING, seal, implement and seasonal disconnect cover bracket plug (used with 359461R1, plug) (will work for 352024R2)
-
9BOLT Hex, 3/8'' - 16 x 7/8'', Gr 5, Full Thd; cap, hex-hd., 3/8-16NC x 7/8''
-
1LOCK WASHER Ext Tooth, 7/8''; WASHER, lock, external-tooth, 7/8''
-
8BOLT Hex, 3/8'' - 16 x 5/8'', Gr 5, Full Thd;
-
1PLUG; pipe, sq-socket, 3/8''
-
8BOLT Hex, 3/8'' - 16 x 7/8'', Gr 5, Full Thd; cap, hex-hd., 3/8-16NC x 7/8''
-
4BOLT Hex, 3/8'' - 16 x 3/4'', Gr 5;
-
4LOCK WASHER 3/8''; WASHER, LOCK, 3/8''
-
3BOLT Hex, 7/16'' - 14 x 2 3/4'', Gr 5;
-
3LOCK WASHER 7/16''; WASHER, LOCK, 7/16''
-
211PAWL; torque amplifier operating handle (see note B)
-
1NO LONGER SERVICED; PIN, cotter, 1/16 x 1/2''
-
1WASHER 1/4''; plain, 9/32 I.D x 5/8'' O.D. x no. 16 ga.
-
232PIN; torque amplifier operating handle pawl grip (see note B)
-
261SPRING; torque amplifier operating handle pawl control grip (see note B)
-
1COTTER PIN 1/8'' x 1''; PIN, SPLIT (COTTER), 1/8'' x 1''
-
1NUT 9/16''-18, G5; hex., 9/16-18NF
-
1LOCK WASHER 9/16''; WASHER, LOCK, 9/16''
-
1WASHER; plain, 25/32'' I.D. x 1-3/8'' O.D. x no. 11 ga.
-
301SHEAVE; FITTING, lubrication, straight, drive type, 3/16'' (torque amplifier operating handle) (optional with 443566) (see note B)
-
301LUBE NIPPLE 3/16'' x .55'' lg, Drive; FITTING, lubrication, straight, drive type, 3/16'' (torque amplifier operating handle) (optional with 273354) (see note B)
-
311SUPPORT 1/2'' x 1''; PIN, dowel, 1/2 x 1'' (torque amplifier operating handle stop pin) (see note B)
-
1HOURMETER Jam, 1/2''-20, G5; NUT, jam, hex., 1/2-20NF
-
331SPRING; return, torque amplifier operating handle (see note B)
-
1BOLT Hex, 3/8'' - 16 x 5/8'', Gr 5, Full Thd;
-
1LOCK WASHER 3/8''; WASHER, LOCK, 3/8''
-
351SPRING; clutch pedal return
-
1JAM NUT Jam, 1/2''-13, G5; Farmall 400 Series tractors Jam, 1/2''-13, G5
-
1PULLEY; SCREW, set, sq-hd., 1/2-13NC x 2-1/4'' (Farmall 400 Series tractors)
-
371FITTING; lubrication, straight, drive type, 3/16''
-
392PIN; torque amplifier release lever (see note B)
-
2COTTER PIN 1/8'' x 1''; PIN, SPLIT (COTTER), 1/8'' x 1''
-
4WASHER 1/2'' ID x 7/8'' OD x 16 ga; plain, 17/32'' I.D. x 7/8'' O.D. x no. 16 ga.
-
402LUBE NIPPLE 1/8''-27 x .66 lg; NIPPLE, LUBE, (Torque amplifier clutch release shaft) (optional with 119512) (see note B) 1/8''-27 x .66 lg
-
402LUBE NIPPLE 45 Degree Elbow, 1/8'' - 27 NPTF; FITTING, lubrication, straight, 1/8'' (torque amplifier clutch release shaft) (optional with 109461) (see note B)
-
422NO LONGER SERVICED; KEY, woodruff, 5/32 x 3/4'' (torque amplifier clutch release shaft) (see note B)
-
431CLEVIS; engine clutch to troque amplifier clutch control (see note B)
-
1HOURMETER Jam, 1/2''-20, G5; NUT, jam, hex., 1/2-20NF
-
1COTTER PIN 1/8'' x 1''; PIN, SPLIT (COTTER), 1/8'' x 1''
-
1AXLE PIN; PIN, rod end, 1/2 x 1-27/64''
-
442LUBE NIPPLE 1/8''-27 x .66 lg; NIPPLE, LUBE, (Clutch release shaft) (optional with 119512) 1/8''-27 x .66 lg
-
442LUBE NIPPLE 45 Degree Elbow, 1/8'' - 27 NPTF; FITTING, lubrication, straight, 1/8'' (clutch release shaft) (optional with 109461)
-
461SPRING; torque amplifier clutch release shaft lever
-
471PIN; clutch operating rod yoke
-
1COTTER PIN 3/16'' x 1''; Pin, Split (Cotter), 3/16'' x 1''
-
1JAM NUT Jam, 5/8''-11, G5;
-
1PIN; std-hd., drilled, 1/2 x 1-15/16''
-
1COTTER PIN 3/16'' x 1''; Pin, Split (Cotter), 3/16'' x 1''
-
501SLEEVE; COUPLING, transmission driving shaft (for tractors not equipped with torque amplifier)
-
511SHAFT; clutch (for tractors not equipped with torque amplifier)
-
521SHAFT; clutch, w/sleeve, 364432R91 (for tractors equipped with torque amplifier with independent power take-off drive)
-
531SLEEVE CYLINDER; SLEEVE, clutch shaft, w/ring, 364411R1 (will work for 362568R1) (see note B)
-
53A1SPRING; RING, snap, clutch shaft sleeve (used only in sleeves with internal groove for snap ring) (see note B)
-
551BALL BEARING; BEARING, torque amplifier clutch release (optional with 368956R91) (see note B)
-
551BEARING; torque amplifier clutch release (optional with 362028R91) (see note B)
-
561RING; SLEEVE, torque amplifier clutch release (see note B)
-
572SPRING; torque amplifier clutch release sleeve (see note B)
-
581FORK; torque amplifier clutch release (see note B)
-
591SCREW; lock, torque amplifier clutch release fork (1-1/8'' long) (not used on tractors equipped with electrall) Farmall 400 Series
-
1JAM NUT Jam, 3/8''-16, G5;
-
612PIVOT; torque amplifier clutch release sleeve (see note B)
-
622THRUST WASHER; torque amplifier clutch release shaft (see note B)
-
632RING; RETAINER, torque amplifier clutch release shaft (see note B)
-
3BOLT Hex, 3/8'' - 16 x 1'', Gr 5;
-
3LOCK WASHER 3/8''; WASHER, LOCK, 3/8''
-
652WASHER; KEY, clutch release fork
-
661FORK; clutch release
-
2NO LONGER SERVICED;
-
2LOCK WASHER 3/8''; WASHER, LOCK, 3/8''
-
671PIVOT; SLEEVE, clutch release
-
681PIPE; grease, clutch release bearing (used only with sleeve, 359022R2, has threaded hole)
-
691LUBE NIPPLE 5/16''-32 x .66 lg; FITTING, lubrication, straight, 5/16-32NF (used with pipe, 365720R1) (optional with 109368)
-
701BALL BEARING; BEARING, ball, clutch release (will work for 361407R91 and 362027R91) (optional with 365868R91 and 367153R91)
-
701BEARING; ball, clutch release (will work for 361407R91 and 362027R91) (optional with 365867R91 and 367153R91)
-
701BEARING; ball, clutch release (will work for 361407R91 and 362027R91) (optional with 365868R91)
-
711BALL BEARING 25mm ID x 52mm OD x 15mm W; BEARING, clutch pilot
Select
Ref.
Qty
6Availability
Part #
179835Description
BOLT Hex, 3/8'' - 16 x 5/8'', Gr 5, Full ThdImg
Select
Ref.
Qty
9Availability
Part #
413-1036Description
BOLT Hex, 5/8'' - 11 NC x 2-1/4'', Gr 5Img
Select
Ref.
Qty
9Availability
Part #
179838Description
BOLT Hex, 3/8'' - 16 x 7/8'', Gr 5, Full ThdImg
Select
Ref.
Qty
1Availability
Part #
253070R1Description
O-RING 0.139'' Thk x 0.859'' ID, -212, Cl 5, 75 DuroImg
Select
Ref.
Qty
9Availability
Part #
179838Description
BOLT Hex, 3/8'' - 16 x 7/8'', Gr 5, Full ThdImg
Select
Ref.
Qty
8Availability
Part #
179835Description
BOLT Hex, 3/8'' - 16 x 5/8'', Gr 5, Full ThdImg
Select
Ref.
Qty
8Availability
Part #
179838Description
BOLT Hex, 3/8'' - 16 x 7/8'', Gr 5, Full ThdImg
Select
Ref.
Qty
1Availability
Part #
179835Description
BOLT Hex, 3/8'' - 16 x 5/8'', Gr 5, Full ThdImg
Select
Ref.
40Qty
2Availability
Part #
219-36Description
LUBE NIPPLE 45 Degree Elbow, 1/8'' - 27 NPTFImg
Select
Ref.
44Qty
2Availability
Part #
219-36Description
LUBE NIPPLE 45 Degree Elbow, 1/8'' - 27 NPTFImg
Select
Ref.
71Qty
1Availability
Part #
ST544Description
BALL BEARING 25mm ID x 52mm OD x 15mm WImg